Resetting your Holosun EPS Carry red dot sight back to factory settings can be a useful tool for troubleshooting issues or simply starting fresh. The process is fairly straightforward and only requires a few simple steps. First, you'll need locating the reset button on the back of the sight. This small button is often unmarked but can be easily identified by its position.
- To initiate a factory reset, you'll need to hold down the reset button for a specific duration of approximately 3-5 seconds. You should see a changing illumination pattern on the sight indicating that the reset process is underway.
- When the reset is complete, the display will return to its normal state.
- The red dot sight is now completely reinitialized. You can then proceed with configuring it according to your preferences.
Be sure to always refer to the user manual for specific instructions and details regarding your Holosun EPS Carry red dot sight.
Returning Your Holosun EPS Carry to Basic Settings
Need to Tweak your Holosun EPS Carry Sight back to its Starting configuration? It's Simple. Here's how:
First, ensure the Red Dot is Activated. Then, locate the Button labeled "Mode".
Press and hold this Button for approximately 10 seconds.
You should See a series of Sequences on the Display. This indicates that the EPS Carry is now Restored to its Original configuration.
Once complete, release the Control. Your Holosun EPS Carry is now Operational with all settings at their Factory values.
Resetting the Holosun EPS Carry Red Dot Sight
The Holosun EPS Carry Blue dot sight is a popular choice for concealed carry applications due to its compact size and durable construction. However, like any optical device, it may require periodic calibration. This can be easily accomplished by following these simple steps: First, find the adjustment screws on the side of the sight. These are typically located near the battery compartment. Using a small screwdriver, carefully turn the screws to adjust the point of impact. Begin by making minor adjustments and test fire the sight at various distances to ensure accuracy. Continue this process until you achieve a desired zeroing point.
- Remember that the adjustment screws can be easily damaged if overtightened, so use caution when turning them.
- Confirm that the battery is fresh and properly installed before making any adjustments.
- If you encounter difficulty zeroing your sight, consult the manufacturer's instructions for further assistance or contact Holosun customer support.
Restore Factory Settings for Holosun EPS Carry
To reset your Holosun EPS Carry to its factory settings, you will need to navigate through the sight's menu system. First, activate the optic by engaging the switch located get more info near the side of the unit. Next, utilize the adjustable buttons found upon the holographic display to access the settings menu. Within the menu, locate the "Factory Reset" option and confirm it using the designated button. The EPS Carry will then initiate a reset sequence, which may take a few moments. Once complete, your sight will be restored to its default configuration.
- Note: During the reset process, all user-configured settings will be erased.
Erase Your Holosun EPS Carry Quickly
Need to get your Holosun EPS Carry back to factory settings? It's easier than you think! Here are the simple steps you need to follow:
First, turn off your sight. Then, find the tiny reset button on the side of the sight. Use a small tool like a paperclip or a pin to press and hold the reset button for about 5 seconds. You'll know it worked when the display starts flashing.
- Allow the sight to cycle through its startup sequence. This might take a few moments.
- Your Holosun EPS Carry is now reset to factory default settings!
Return to Factory Settings a Holosun EPS Carry Red Dot
Need to acquire new configuration setup? Here's how to accomplish this to Factory Reset your Holosun EPS Carry Red Dot.
First, ensure the red dot is activated. Next, locate the tiny button on the left/right side of the sight's housing/body. Press and hold this button for a minimum of 5 seconds/3 seconds. You should observe a flashing light/blinking indicator indicating that the reset process has begun/started. Keep holding/pressing the button until the light stops blinking/flashing. Let go the button and your Holosun EPS Carry Red Dot is now completely reinitialized.